Soil Classification

Learning Objectives

  • Understand the purpose of classifying soils in geotechnical engineering.
  • Analyze particle size distribution using Sieve and Hydrometer methods.
  • Calculate and interpret Atterberg Limits for fine-grained soils.
  • Classify soils using the Unified Soil Classification System (USCS) and AASHTO methods.
Soil classification systems allow engineers to group soils with similar engineering properties based on their physical characteristics. The two most common systems are the Unified Soil Classification System (USCS) and the AASHTO Classification System.

Particle Size Analysis

The first step in classification is determining the distribution of particle sizes.

Gradation

The distribution of particle sizes within a soil sample. Soils can be well-graded (wide range of sizes) or poorly graded (uniform size or gap-graded).

Sieve Analysis

Used for coarse-grained soils (gravel and sand). The soil is shaken through a stack of sieves with decreasing mesh sizes.

  • Percent Finer (FF): The percentage of soil passing a specific sieve.
  • Coefficient of Uniformity (CuC_u): Measures the range of particle sizes.
  • Coefficient of Curvature (CcC_c): Measures the shape of the gradation curve.

Gradation Types:

  • Well-graded (W): Wide range of sizes.
  • Poorly graded (P): Uniform size (SP) or gap-graded (GP).

Coefficient of Uniformity

Measures the range of particle sizes in a soil sample; larger values indicate a wider gradation.

Cu=D60D10C_u = \frac{D_{60}}{D_{10}}

Variables

SymbolDescriptionUnit
CuC_uCoefficient of uniformity
D60D_{60}Diameter corresponding to 60% finer by weight
D10D_{10}Diameter corresponding to 10% finer by weight (effective size)

Uniformity Criteria

  • Well-graded Gravel (GW): Cu≥4C_u \ge 4
  • Well-graded Sand (SW): Cu≥6C_u \ge 6

Coefficient of Curvature

Measures the shape of the particle-size gradation curve; used alongside C_u to classify well-graded soils.

Cc=(D30)2D10×D60C_c = \frac{(D_{30})^2}{D_{10} \times D_{60}}

Variables

SymbolDescriptionUnit
CcC_cCoefficient of curvature (or gradation)
D30D_{30}Diameter corresponding to 30% finer by weight
D60D_{60}Diameter corresponding to 60% finer by weight
D10D_{10}Diameter corresponding to 10% finer by weight (effective size)

Curvature Criteria

  • Well-graded soils (GW or SW) must have 1≤Cc≤31 \le C_c \le 3.

Hydrometer Analysis (Stokes' Law)

Used for fine-grained soils (silts and clays) passing the No. 200 sieve. It relies on Stokes' Law, which states that the settling velocity (vv) of a spherical particle in a fluid is proportional to the square of its diameter (DD).

By measuring the specific gravity of the soil-water suspension over time using a hydrometer, engineers can calculate the settling velocities and thus determine the distribution of microscopic particle sizes (e.g., separating silt from clay fractions at the 0.002 mm boundary).

Stokes' Law (Settling Velocity)

Predicts the settling velocity of fine soil particles in suspension; the basis for hydrometer analysis of silts and clays.

v=γs−γw18μD2v = \frac{\gamma_s - \gamma_w}{18 \mu} D^2

Variables

SymbolDescriptionUnit
vvSettling velocity of the particle
γs\gamma_sUnit weight of soil solids
γw\gamma_wUnit weight of water
μ\muDynamic viscosity of the fluid
DDDiameter of the spherical particle

Interactive Sieve Analysis

Interactive Simulation

Explore how particle distribution affects the gradation curve using the simulation below.

Aggregate Grading and Stockpile Blending

Concept and model scope

The three source gradations are synthetic teaching curves. At every opening, percent passing for the blend is the dry-mass-weighted mean of the source percentages. Material retained on one sieve is the difference between passing the next larger opening and passing this opening.

Mix two stockpiles by dry mass and inspect how the blend changes the material passing each sieve.

Controls
Stockpile B dry mass fraction

Percent of the blend dry mass supplied by stockpile B. Stockpile A supplies the remainder.

0%
Dry mass passing (%)0501000.0750.31.184.751937.5Sieve opening (mm, logarithmic scale)
Dashed: A · Dotted: B · Solid: blend · Dot: selected sieve
Passing in stockpile A
67.00%
Passing in stockpile B
30.00%
Blend passing selected sieve
67.00%
Blend retained on selected sieve
12.00%

Atterberg Limits

Atterberg limits are used for fine-grained soils (silts and clays) to describe their consistency at varying water contents.

Atterberg Limits

The water contents at which soil behavior changes between solid, semi-solid, plastic, and liquid states.

Liquid Limit (LL)

The water content at which soil transitions from a plastic to a liquid state.

Plasticity Index (PI)

The range of water content where soil behaves plastically.

Consistency Limits

  • Liquid Limit (LL): The water content at which soil transitions from a plastic to a liquid state. Determined by the Casagrande cup method (25 blows).

  • Plastic Limit (PL): The water content at which soil transitions from a semi-solid to a plastic state. Determined by rolling a 3mm thread.

  • Plasticity Index (PI): The range of water content where soil behaves plastically.

  • Liquidity Index (LI): Used to predict the stress history and in-situ state.

Plasticity Index

The range of water contents over which a fine-grained soil behaves plastically; a key index for classifying clays and silts.

PI=LL−PLPI = LL - PL

Variables

SymbolDescriptionUnit
PIPIPlasticity index
LLLLLiquid limit
PLPLPlastic limit

Liquidity Index

Indicates the in-situ consistency of a fine-grained soil relative to its Atterberg limits; used to predict undrained shear strength.

LI=win−situ−PLPILI = \frac{w_{in-situ} - PL}{PI}

Variables

SymbolDescriptionUnit
LILILiquidity index
win−situw_{in-situ}In-situ water content
PLPLPlastic limit
PIPIPlasticity index

A-Line

An empirical line on the plasticity chart (PI=0.73(LL−20)PI = 0.73(LL - 20)) that separates clay (above) from silt (below).

Unified Soil Classification System (USCS)

The USCS classifies soils into four major groups based on the percentage passing the No. 200 sieve (0.075 mm).

USCS Group Symbols

Primary Letter (Soil Type):

  • G: Gravel (> 50% of coarse fraction is retained on No. 4 sieve)
  • S: Sand (> 50% of coarse fraction passes No. 4 sieve)
  • M: Silt (Passes No. 200, below A-line)
  • C: Clay (Passes No. 200, above A-line)
  • O: Organic (High organic content)
  • Pt: Peat (Highly organic)

Secondary Letter (Gradation or Plasticity):

  • W: Well-graded (Clean gravels/sands with <5%<5\% fines)
  • P: Poorly graded (Clean gravels/sands with <5%<5\% fines)
  • M: Silty (Gravels/sands with >12%>12\% fines)
  • C: Clayey (Gravels/sands with >12%>12\% fines)
  • H: High plasticity (LL>50LL > 50)
  • L: Low plasticity (LL<50LL < 50)

USCS Dual Symbols

Soils with 5% to 12% fines require dual symbols (e.g., SW-SM, GW-GC) to indicate both gradation and the nature of the fines.

Basic USCS Classification Procedure

  1. Determine if the soil is coarse-grained (>50%>50\% retained on No. 200 sieve) or fine-grained (>50%>50\% passes No. 200 sieve).
  2. If coarse-grained, determine if it is Gravel (>50%>50\% of coarse fraction retained on No. 4 sieve) or Sand (>50%>50\% of coarse fraction passes No. 4 sieve).
  3. Determine the percentage of fines. If <5%<5\%, use CuC_u and CcC_c to assign W or P. If >12%>12\%, use Atterberg limits to assign M or C. If 5−12%5-12\%, use a dual symbol.
  4. If fine-grained, plot LL and PI on the Plasticity Chart to classify as Silt (M) or Clay (C) and determine plasticity (L or H).

Interactive Plasticity Chart

Interactive Simulation

Use the chart below to determine the USCS classification for fine-grained soils based on Liquid Limit (LL) and Plasticity Index (PI).

USCS Plasticity Chart

Result
CL
Lean Clay
Liquid Limit (LL)Plasticity Index (PI)A-LineCLMLCHMH

The A-Line separates clays (above) from silts (below). The vertical line at LL=50 separates low plasticity (L) from high plasticity (H).

AASHTO Classification System

The AASHTO classification system is used primarily for highway subgrade classification. Soils are classified into seven major groups: A-1 to A-7.

Group Index (GI)

Used to evaluate the quality of a soil as a subgrade material. The higher the GI, the poorer the soil.

Group Index

AASHTO index that quantifies the suitability of a soil as a highway subgrade material; higher values indicate poorer quality.

GI=(F200−35)[0.2+0.005(LL−40)]+0.01(F200−15)(PI−10)GI = (F_{200} - 35)[0.2 + 0.005(LL - 40)] + 0.01(F_{200} - 15)(PI - 10)

Variables

SymbolDescriptionUnit
GIGIGroup Index
F200F_{200}Percent passing No. 200 sieve (whole number)
LLLLLiquid limit
PIPIPlasticity index

Group Index Calculation Rules

  • If GI<0GI < 0, set GI=0GI = 0.
  • Round to the nearest whole number.
  • For Groups A-2-6 and A-2-7, use only the second term (PI term).

Use this workflow to choose the requested classification system, confirm the sample and test data, then report the classification with its basis. Apply the current project-specified standard and its required procedures; the linked standards are classification references, not substitutes for engineering property testing.

Soil Classification and Reporting

Select and report a classification only after confirming the classification system, representative sample, gradation, and plasticity data.

USCS and AASHTO are classification systems, not substitutes for strength, compressibility, or performance testing. Apply the current project-specified standard and its required test methods; this workflow sets no design acceptance threshold.

Soil Classification and ReportingSelect and report a classification only after confirming the classification system, representative sample, gradation, and plasticity data.. USCS and AASHTO are classification systems, not substitutes for strength, compressibility, or performance testing. Apply the current project-specified standard and its required test methods; this workflow sets no design acceptance threshold.. Start → Confirm project purpose and required classification system; Confirm project purpose and required classification system → At least one classification system specified?; At least one classification system specified? — Yes → Representative sample and required data available?; At least one classification system specified? — No → Hold: confirm classification system required; Representative sample and required data available? — Yes → Determine particle-size fractions and percent passing; Representative sample and required data available? — No → Hold: obtain representative sample or missing data; Determine particle-size fractions and percent passing → USCS classification required?; USCS classification required? — Yes → More than 50% retained on No. 200 sieve?; USCS classification required? — No → Proceed with AASHTO classification only; Proceed with AASHTO classification only → Apply AASHTO group rules and calculate GI as specified; More than 50% retained on No. 200 sieve? — Yes → Use coarse fraction, gradation, fines, and plasticity rules; More than 50% retained on No. 200 sieve? — No → Use liquid limit, plasticity index, and A-line position; Use coarse fraction, gradation, fines, and plasticity rules → Record USCS group symbol and descriptive name; Use liquid limit, plasticity index, and A-line position → Record USCS group symbol and descriptive name; Record USCS group symbol and descriptive name → AASHTO also requested?; AASHTO also requested? — Yes → Apply AASHTO group rules and calculate GI as specified; AASHTO also requested? — No → Retain USCS classification for this request; Apply AASHTO group rules and calculate GI as specified → Report system, test basis, symbol, and limitations; Retain USCS classification for this request → Report system, test basis, symbol, and limitations; Report system, test basis, symbol, and limitations → End

Start → Confirm project purpose and required classification system; Confirm project purpose and required classification system → At least one classification system specified?; At least one classification system specified? — Yes → Representative sample and required data available?; At least one classification system specified? — No → Hold: confirm classification system required; Representative sample and required data available? — Yes → Determine particle-size fractions and percent passing; Representative sample and required data available? — No → Hold: obtain representative sample or missing data; Determine particle-size fractions and percent passing → USCS classification required?; USCS classification required? — Yes → More than 50% retained on No. 200 sieve?; USCS classification required? — No → Proceed with AASHTO classification only; Proceed with AASHTO classification only → Apply AASHTO group rules and calculate GI as specified; More than 50% retained on No. 200 sieve? — Yes → Use coarse fraction, gradation, fines, and plasticity rules; More than 50% retained on No. 200 sieve? — No → Use liquid limit, plasticity index, and A-line position; Use coarse fraction, gradation, fines, and plasticity rules → Record USCS group symbol and descriptive name; Use liquid limit, plasticity index, and A-line position → Record USCS group symbol and descriptive name; Record USCS group symbol and descriptive name → AASHTO also requested?; AASHTO also requested? — Yes → Apply AASHTO group rules and calculate GI as specified; AASHTO also requested? — No → Retain USCS classification for this request; Apply AASHTO group rules and calculate GI as specified → Report system, test basis, symbol, and limitations; Retain USCS classification for this request → Report system, test basis, symbol, and limitations; Report system, test basis, symbol, and limitations → End

  • Start: terminator
  • Confirm project purpose and required classification system: process
  • At least one classification system specified?: decision
  • Representative sample and required data available?: decision
  • Hold: obtain representative sample or missing data: terminator
  • Hold: confirm classification system required: terminator
  • Determine particle-size fractions and percent passing: process
  • USCS classification required?: decision
  • More than 50% retained on No. 200 sieve?: decision
  • Use coarse fraction, gradation, fines, and plasticity rules: process
  • Use liquid limit, plasticity index, and A-line position: process
  • Record USCS group symbol and descriptive name: document
  • AASHTO also requested?: decision
  • Proceed with AASHTO classification only: process
  • Apply AASHTO group rules and calculate GI as specified: process
  • Retain USCS classification for this request: process
  • Report system, test basis, symbol, and limitations: document
  • End: terminator
Key Takeaways
  • USCS is the preferred system for geotechnical engineering, while AASHTO is used for highway engineering.
  • Sieve Analysis separates coarse particles; Hydrometer Analysis utilizes Stokes' Law to determine the size distribution of fine particles (silts/clays) based on settling velocity.
  • The Plasticity Chart uses the A-line (PI=0.73(LL−20)PI = 0.73(LL-20)) to separate clays (above) from silts (below).
  • Atterberg Limits (LL, PL, PI) are critical for classifying fine-grained soils and predicting their engineering behavior (swelling, shrinkage, strength).
  • Group Index (GI) in AASHTO quantifies the suitability of soil as a subgrade material; higher GI = poorer quality.